Essential Plumbing Insights for Bathtub Installation
Essential Plumbing Insights for Bathtub Installation
Blog Article
We've unearthed this post on How to Install a Bathtub Yourself down the page on the internet and felt it made perfect sense to discuss it with you over here.
Mounting a bathtub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is conveniently available, the task can move easily; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub as well as set in the brand-new one. Make sure you have qualified yourself for the work and also fit trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This short article will certainly assist you mount a brand-new tub in your shower room if you have actually already purchased a brand-new bathtub as well as do not need to alter the setup of your previous water pipes.
Your devices and material checklist must consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipelines have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in area in between the faucet as well as the sink. Safeguard the tap in position with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The former kind must be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the required position. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub till the level reads degree.
To mount taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Turn on the water supply and also check all joints as well as new pipework for leaks and tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub needs to wait until the bathtub has actually been utilized a minimum of when as this will resolve it into its last placement.
Getting ready for the Installment
First of all, the sustaining framework supplied with the bath should be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that article on How to Install a Bathtub Yourself through an associate on another web page. Do you know somebody who is serious about Tools You Need to Install a New Bathtub ? Take a moment to promote it. Many thanks for taking the time to read it.
Quality solution? Call. Report this page